INSTALLATION GUIDE AND USER’S MANUALFastlane Pool
• Outside the pool, thread in the male portion of the street elbow(#6) into the tailpiece of the thru-wall fitting (#8).• From inside the pool, thread
the pump foot. Use the provided screws to clamp the pump on thepower unit handle.Attach the pump union nuts to both fittings of the pump. Makesure t
Next, take the 4-1/4” long piece and glue a slip x slip 90º elbowonto one end. At the other end of this pipe another street elbowwill be glued on, bu
12ELECTRICAL REQUIREMENTS AND CONNECTIONS (60Hz)Consider the electrical requirements for the specific installationbefore locating the Water Quality Sy
ELECTRICAL REQUIREMENTS (50Hz)Fastlane Pool without Heater Wiring InstructionsA licensed electrician should make all electrical connections. Thestand
14TYPICAL SETTINGSSet Point : 59°F to 104°F / Factory set at 84°FFilter Cycle Duration: 0 to 24 hrs / Factory set at 24 hrsMax Set Point: 59°F to 104°
Off ModeThis mode allows you to stop alloutputs for 30 minutes to per-form a quick spa maintenance.Press and hold Key 1 key for 5secs to activate the
16USING THE FASTLANE SWIM UNITIt is now acceptable to begin using the Fastlane Swim Unit.Remove and unwrap the two (one for use, one extra) wireless c
Daily:• Test for free chlorine after swimming, or at least a few times a week.• Add chlorine to maintain free chlorine levels between 0.5 and1.5 ppm.•
18RETRACTABLE SECURITY COVER INSTALLATIONRetractable Cover Parts KitContainer AQty 1 - 3" dia. PVC roller system, 102” long, inside of whichwill
1Endless Pools, Inc. provides for every aspect of a Fastlane Pool project. This manual assists in the installation process, as well as the general mai
2) Using the provided 2" deck screws, attach the third 8'-11"cedar plank to the top of the two planks that are alreadyattached to the p
making sure the ends of the top plank line up with the ends ofthe vertical plank. The top plank should overhang into the poolenough so that its back e
7) In order to best accommodate the ladder, create a notch meas-uring 22 1/2" long and 2 1/2" deep in the center (or in a pre-ferred ladder
the front corners of the pool. Repeat for the other side, and usethe 2" deck screws to attach these pieces to the front corners ofthe pool.10) Ag
232) Place the notch cutout piece (saved from Step 7 of Building theDeck) on the horizontal deck plank at the rear of the pool sothat the outside edge
242) Install the track splice between the adjoining tracks. Slide theplate into the extrusion end of both tracks before placing thesecond track on the
256) Slide the handle over the hub and secure it to the hub using the5/16" bolt and washer.7) Repeat the process for the other end of the pipe, b
2610) Now repeat the process at the other end of the pool for theother anchor bracket. Drill the hole, and using the washer andlag bolt, loosely ancho
27way across the pool. Replace the black end guide top half.13) Fasten the fabric to the 3" PVC drum using the provided 1/2"pan head screws
28
RECEIVING THE FASTLANE POOLThe Fastlane Pool is shipped via UPS and contains at least 16 packages:Box 1: Fastlane Pool Power UnitBox 2: Biodegradabl
30Wiring Schematic for 60hz Heater/ControllerGroundLine 2NeutralLine 1G/yRWBGroundLine 2NeutralLine 1BWRG/yWiring Schematic for 60hz Power Unit 230v,
Wiring Schematic for 50hz Heater/ControllerWiring Schematic for 50hz Power Unit 220v, 30 amp, single phase31
32FASTLANE POOL™ LIMITED WARRANTYENDLESS POOLS, INC. WARRANTS TO THE ORIGINAL PURCHASER OF THE FASTLANE POOL MANUFAC-TURED BY US TO BE FREE FROM DEFEC
Endless Pools,Inc.• 1601 Dutton Mill Rd • Aston, PA 19014-2931800-910-2714 • 610-497-8693 fax • www.myendlesspool.comOM28 10-09
GROUND PREPARATIONThe surface the Fastlane Pool is to be assembled on must be firmand level. The Fastlane Pool must be installed as level as possi-bl
4. Connect the top tubes (Parts B and C) together. NOTE: Theshorter tube (Part C) is always the last tube on the rightwhen facing the pool wall. (Refe
6. Insert and connect the top corner tubes (Part D). It may behelpful to insert both ends of corner tube into the correspondingliner sleeves, and the
6and the six 10-32 stainless steel lock nuts provided. Secure thebond wire that has been fed up through the turning vanes underone of the six screws.
13. Re-install the throat that was removed previously in Step 4.14. Place the Swim Unit on the ground and roll it close to theFastlane Pool location f
8SKIMMER ASSEMBLY1. Align the skimmer opening with the opening in the housing.Use the hardware provided with the skimmer to attach theskimmer to the h
Comments to this Manuals